EIGRP Enabler #3 – Answers

By certskills March 23, 2017 12:05

EIGRP Enabler exercise 3 asked you to configure four routers, specifically to add the EIGRP network commands. If you’ve not seen these before, check out the Routing Protocol Enabler intro post. Otherwise, it’s straightforward, so keep going!

The Topology

It is probably best to have the exercise post on the screen at the same time you look at this post. If not, for convenience, here’s a copy of the topology figure for this exercise.

EIGRP Enabler Topology


The Answers

I promised short, sweet, and to the point. Here are the answers!

Answers: Router R1


Answers: Router R2


Answers: Router R3


Answers: Router R4


Comments and Explanations – R1

R1 requires some thought because you must calculate the subnet ID of each subnet off each interface, and find the ACL wildcard mask to use that matches the subnet mask on each interface, following a process like this:

  1. Begin with each interface’s IP address and subnet mask
  2. Calculate the subnet ID, which will be the first parameter in the network command
  3. Invert the subnet mask, which will be the second parameter in the network command

Because of how the exercise is worded, you should have three network commands, one matching the subnet off each of the interfaces on R1.

Most of the math should be straightforward, but the numbers might give you reason to be suspicious. Two of the network commands have a subnet ID that ends with a .128 – both are correct –  but with two different subnet masks, that kind of answer can appear to be incorrect.

R1 has another suspicious number for the last network command. Note that R1’s G0/3 happens to be a zero subnet, so the EIGRP network subcommand uses what looks like class B network number The command network, with no wildcard, would be incorrect per the exercise, because it would match all addresses in the class B network. The network command matches all the addresses in the correct zero subnet off R1’s G0/3, meeting the requirements – but looking a little strange.

And if that last paragraph caused you more pain than if you just hadn’t read it: trust the process. The first number is the subnet ID, and the second is the inverse of the subnet mask (that is, – subnetmask). Trust the process.


Comments and Explanations – R2

R2 requires the least thought of all the routers. To match a single IP address, use wildcard mask of For the number preceding the wildcard mask in the network command, use the interface IP address. The result: each network command matches an interface IP address, and only that address, enabling EIGRP on that interface.


Comments and Explanations – R3

R3 uses the same “match subnet” logic as R1, with the same process. Just work the process!

As for these specific answers, the two network commands whose subnet IDs end in .128 again may look strange sitting right above/below each other, but are correct. And the fact that all these subnet IDs do not end in 0 can cause many people to mistrust their math. Once again, subnetting math shows up in the most unlikely of places!


Comments and Explanations – R4

For R4, you needed to start by identifying the various classful networks (class A, B, or C networks) used on the interfaces. Then, to configure one network command to match each classful network, just configure the network command with that classful network number, and with no wildcard mask. Simple enough.

In this case, R4 has three interfaces, all three of which connect to class B network Therefore, R4 needs only a single command: network

EIGRP Enabler #3
IPv6 Icky EUI-64 Drill 1
By certskills March 23, 2017 12:05
Write a comment


  1. Ruben Duarte May 15, 16:28

    These posts are a little bit quiet, but I just want to thank you for all of these!
    It’s great practice 🙂

    Reply to this comment
  2. Mit May 14, 10:49

    Hi Wendell,

    Had a question….

    For neighborship to form in eigrp, is it mandatory that the two interfaces on a link must be on same subnet?

    Reply to this comment
  3. Bav October 30, 09:37

    Lesson of the day. Keep practicing subnetting.

    Reply to this comment
View comments

Write a comment

Comment; Identify w/ Social Media or Email


Subscribe to our mailing list and get interesting stuff and updates to your email inbox.

Thank you for subscribing.

Something went wrong.