Back to homepage

Config Lab CCNA Vol 1 Part 3

Config Lab: L2 EtherChannel 2

Config Lab: L2 EtherChannel 2

🕔15:05, 7.Sep 2021 Both layer 2 EtherChannel and layer 3 EtherChannel use the same set of commands to create the channel. You have the option to use static configuration or one of two dynamic protocols to negotiate the formation of a trunk (LACP Read Full Article
Config Lab: L2 EtherChannel 1

Config Lab: L2 EtherChannel 1

🕔13:05, 7.Sep 2021 EtherChannel takes a big step towards improving STP. With two links between switches, but without using EtherChannel, each instance of STP could use only one of the links blocking the other link. With a layer 2 EtherChannel, STP treats the Read Full Article
Config Lab: RSTP Config 2

Config Lab: RSTP Config 2

🕔11:05, 7.Sep 2021 LAN switches use many default settings that work without you having to do anything, and oftentimes, you can leave those default settings as-is. However, with Spanning Tree Protocol (STP), and its better cousin Rapid STP (RSTP), you should configure some Read Full Article
Config Lab: RSTP Config 1

Config Lab: RSTP Config 1

🕔09:05, 7.Sep 2021 LAN switches use many default settings that work without you having to do anything, and oftentimes, you can leave those default settings as-is. However, with Spanning Tree Protocol (STP), and its better cousin Rapid STP (RSTP), you should configure some Read Full Article
Config Lab: Trunking for Only Some VLANs

Config Lab: Trunking for Only Some VLANs

🕔19:05, 3.Sep 2021 VLAN trunks between Cisco Catalyst switches support all VLANs known to the switches. As time progresses, each time the switch learns of a new VLAN, the VLAN trunk also allows traffic in the VLAN to use the trunk. Is that Read Full Article
Config Lab: Basic VLANs

Config Lab: Basic VLANs

🕔17:05, 3.Sep 2021 Configuring VLANs on access switches may be the most common repetitive configuration task in many networks. So what do you configure when adding new access devices to new VLANs? This lab gives you a chance to remember and exercise those Read Full Article
Config Lab: Trunking Puzzle 1

Config Lab: Trunking Puzzle 1

🕔15:05, 3.Sep 2021 You can memorize VLAN trunking commands by staring at a table – but you will remember them much better if you try different combinations in sample labs, especially if you try them from the CLI of some gear or simulator. Read Full Article
Config Lab: Data and Voice VLAN 2

Config Lab: Data and Voice VLAN 2

🕔13:05, 3.Sep 2021 Ready to prepare some access switches to support IP phones? This latest config lab sets up the problem for that specific task. The lab shows the common access switch configuration required when you connect a switch port to a phone, Read Full Article
Config Lab: Data and Voice VLANs 1

Config Lab: Data and Voice VLANs 1

🕔11:05, 3.Sep 2021 Creating a VLAN is simple: just configure the vlan number command. However, even in a small network with four switches, like the one used in this next lab, a VLAN config lab can give you a few things to think Read Full Article
Config Lab: VLAN Basics 3

Config Lab: VLAN Basics 3

🕔09:05, 3.Sep 2021 Short and sweet – how do you create new VLANs and put a couple of ports in each? Today’s lab should be an easy and automatic process before you go take the CCNA exam, but getting one more rep in Read Full Article

Subscribe

Subscribe to our mailing list and get interesting stuff and updates to your email inbox.

Thank you for subscribing.

Something went wrong.

Search

Categories